Hard Floor care tips based on traffic conditions

Dry soils such as sand, grit and dust are invariably found on hard surface floors. For the most part, their presence is not a significant problem. However, this can change significantly when people walk across and mobile equipment (trolleys, pushchairs, wheelchairs etc) roll over the floor.

These dry soils have sharp edges. Once people and equipment are introduced they can start abrading, eroding and otherwise damaging the floor and its finish.

The number of people and equipment travelling on a floor is referred to as “Traffic” and the amount of foot traffic on the floor will help determine the amount and type of cleaning and maintenance the floor will need.

Rotary buffer

To help cleaning professionals better understand the concept of foot traffic, the following guidelines may help:

Low Traffic: A low-traffic environment is typically a small office or retail store. Such a facility will have about 100 to 500 people walking through it each day. Daily sweeping/vacuuming may be required to remove light debris, dust etc but thorough (wet) floor maintenance may only be required on a weekly basis.

Medium Traffic: While some environments may fall into the high traffic category, medium sized buildings are considered medium foot traffic environments. These facilities typically have 500 to 1,500 people walking through them and will require daily cleaning.

High Traffic: Environments that include 1,500 or more people per day walking on their floors include facilities such as large office buildings, large station concourses, airports, hospitals and large schools and colleges. The floors here are continually under attack and will require floor maintenance multiple times throughout the day.

It is also important to realise that certain areas within a facility may have multiple traffic patterns. Invariably, lobbies and entries into retail stores can be high traffic areas while other areas within the facility may have medium or even low traffic.

To ensure proper floor maintenance, cleaning professionals must be clear which areas need the most frequent attention. This ensures the floors are properly maintained, reduces costs, and can help reduce the frequency of expensive floor restoration.

In all cases, variables such as weather conditions, the installation of entrance matting, etc., can play a role in the amount of care and attention a floor needs.

Into the Light

Advertisements

Cleaning warehouse floors – a Health & Safety issue

Warehouses through their very nature are high risk locations. High level racking systems, fork lift trucks moving back and forth, pallets of goods at ground level and at height, and areas where lighting fails to adequately penetrate creating poor visibility.

It is therefore extremely important to ensure that suitable precautions are taken to maintain and enhance safety for all building users, and nowhere is this more important than by keeping floors clear of litter and free from dirt and spillages.

Slips, trips and falls remain the most common cause of workplace accidents, accounting for almost 1/3 of all major workplace injuries in 2012/13 (HSE statistics). Recent surveys highlight the fact that while slips and trips remain a priority concern for employers, few felt that organisations are fully effective at controlling the slip and trip risk.

To help companies overcome some of the issues associated with cleaning floors in warehouses and other industrial buildings, there is a wide range of sweeping machines available from various manufacturers and suppliers to meet a variety of needs and budgets.

Where large warehousing facilities exist, the Comac CS100/CS120 battery, diesel or bi-fuel (LPG) powered ride-on sweepers come in to their own.

Designed to easily collect solid debris as well as light dust, the CS100/CS120 is at the top of the range in terms of power, capacity, durability and heavy duty performance.

A debris hopper with a capacity of over 400 litres allows the CS100 to cover an area of up to 16,200m2/hour.

Once a warehouse floor has been cleared of solid debris, litter and dust, it is essential that the floor is thoroughly cleaned to remove residual liquid spillages, especially those of a greasy or oily nature which could pose serious slip hazards.

The Comac Ultra 100B is a scrubber drier compact in size yet innovative in its design and is perfectly suited to both maintenance and deep cleaning of medium to large sized areas.

Ultra-RGB[1]

With a working width of 1,000mm and a solution tank of 200 litres, the Ultra 100B can cover an area up to 6,500m2 per hour. The machine has been designed to make the operator’s job as comfortable as possible and to be extremely user friendly for even unskilled staff.

The Ultra 100B also boasts excellent low noise levels thanks to the suction motor being fitted inside a double wall tank made of insulating polyethylene.

Maintaining the appearance, safety and integrity of warehouse floors is essential to meet strict Health & Safety regulations, as well as ensuring that the working environment is both safe and productive for those working there.

By using high quality floor cleaning machines, designed to meet the demands of today’s busy working environments, it is easier for a cleaning contractor or warehouse operator to meet those regulations and in so doing to maintain and enhance safety and to increase productivity.

For more information on the Comac range of sweepers and scrubber driers contact Simon Collins of Industrial Floorcare Machines (UK) by email at simon@industrialfloorcaremachines.com.

Cleaning and maintenance of stone floors

The first step in proper stone care and maintenance is to understand your stone’s geological classification and composition. This information will help you to identify what cleaning products to use and how best to care for your natural stone.

Natural stone is categorised into three basic geological classifications by their respective formation processes

  1. Sedimentary
  2. Metamorphic
  3. Igneous

Additionally, stones in each category can be either Calcareous or Siliceous.

Calcareous stone is composed mainly of calcium carbonate, a chemical compound commonly found in natural stone, shells and pearls. Calcium Carbonate is sensitive to acidic solutions so mild, non-acidic cleaners are recommended.

Siliceous stone, as the term implies, is one composed primarily of silicates, such as quartz, feldspar, mica, etc. As such, a siliceous stone is generally resistant to most acids found although acidic cleaners are still not recommended, as these stones may contain trace levels of minerals that are acid sensitive.

The following chart is a helpful guide:

Stone type table

To get the longest life and to preserve the beauty of natural stone, follow these simple tips:

Dust Mopping: Dust mop interior floors frequently using a clean non-treated dry dust mop. Sand, dirt and grit are abrasive and can damage natural stone.

Mats/rugs: Entrance matting systems or area rugs inside and outside an entrance will help to minimise the sand, dirt and grit that may otherwise scratch the stone floor. Be sure that the underside of the mat or rug is slip resistant.

Marble floor in hotel

Vacuum cleaners: If used, be sure the metal or plastic attachments or the wheels are not worn as they can scratch the surface of some stones.

Spills: Blot the spill with a paper towel immediately. Don’t wipe the area, it will spread the spill. Flush the area with water and mild detergent and rinse several times. Dry the area thoroughly with a soft cloth. Repeat as necessary.

Cleaning:

  • Clean stone surfaces with a neutral cleaner or stone soap and warm water.
  • An excessive concentration of cleaner or soap may leave a film and cause streaks. Follow manufacturer recommendations.
  • Rinse the surface thoroughly after washing with detergent or soap solution and ensure the floor is dried.
  • For large areas such as entrance lobbies, corridors etc use a scrubber drier that will wash, scrub and dry in a single pass.
  • For even larger outside areas, a ride-on scrubber drier can be employed which will also be a more productive means of cleaning large areas.

natural-stone-tiles-exterior-floors-55300-1678037ECO_1298_HR_Lichen_crop

  • In outdoor pool or patio areas, flush with clear water and use mild bleach solution to remove algae or moss.

Cleaning Products:

  • Many suppliers offer products used for stone cleaning.
  • Products containing lemon, vinegar or other acids may dull or etch calcareous stones.
  • Scouring powders or creams often contain abrasives that may scratch certain stones.
  • Many commercially available rust removers (laundry rust stain removers, toilet bowl cleaners) contain trace levels of hydrofluoric acid (HF). This acid attacks silicates in addition to other minerals. All stones, including granite and quartzite, will be attacked if exposed to HF.

Sealing

Sealing is a common step taken on some stones as an extra precaution against staining. In fact, the sealing products used in the stone industry are ‘impregnators” which do not actually seal the stone, but more correctly act as a repellent rather than a sealer.

Sealing does not make the stone stain proof, rather it makes the stone more stain resistant. When consulting with your stone supplier, you may find that many stones do not require sealing. However, applying an impregnating sealer is a common practice.

When considering sealing, remember that sealing the stone does not make the stone stain proof, it makes it more resistant to staining.

If a sealer is applied in a food preparation area, be sure that it is non-toxic and safe for use.

Consult with your supplier or sealing manufacturer specific to the type of sealer and frequency of use recommended.

Stain Identification Tips

Identifying the type of stain on the stone surface is the key to removing it. Stains can be oil based, organic, metallic, biological, ink based, paint based, acid based. If you don’t know what caused the stain, consider likely staining agents that may have been present. Here are some questions you should consider:

Where is the Stain Located?

  • Is it near a plant, a food service area, an area where cosmetics are used?
  • What colour is it?
  • What is the shape or pattern?
  • What occurs in the area around the stain?

Stain Removal Steps

Surface stains can often be removed by cleaning with an appropriate cleaning product.

What Type of Stain is it?

The following sections describe the types of stains you may have to deal with and the appropriate household chemicals to use and how to prepare and apply a poultice to remove the stain.

Oil-based (grease, tar, cooking oil, cosmetics) An oil-based stain will darken the stone and normally must be chemically dissolved so the source of the stain can be flushed or rinsed away. Clean gently with a soft, liquid cleanser.

Organic (coffee, tea, wine, fruit, tobacco, paper, food, urine, leaves, bark, bird droppings) May cause a pinkish-brown stain and may disappear after the source of the stain has been removed. Outdoors, with the sources removed, sun and rain action will generally bleach out the stains. Indoors, clean with a mild hydrogen peroxide solution.

Metallic (iron, rust, copper, bronze) Iron or rust stains are orange to brown in color and follow the shape of the staining object such as nails, bolts, screws, cans, flower pots, metal furniture.

Copper and bronze stains appear as green or muddy-brown and result from the action of moisture on nearby or embedded bronze, copper or brass items. Metal stains must be removed with a poultice.

Deep-seated, rusty stains are extremely difficult to remove and the stone may be permanently stained.

Biological (algae, mildew, lichens, moss, fungi) Clean with a recommended cleaning solution, generally containing ammonia, bleach, or hydrogen peroxide.

Paint Small amounts can be removed with lacquer thinner or scraped off carefully with a razor blade. Heavy paint coverage should be removed only with a commercial “heavy liquid” paint stripper available from DIY stores and paint centres.

These strippers normally contain caustic soda. Do not use acids or flame tools to strip paint from stone. Paint strippers can etch the surface of the stone; re-polishing may be necessary.

Follow the manufacturer’s directions for use of these products, and flush the area thoroughly with clean water. Protect yourself with rubber gloves and eye protection, and work in a well-ventilated area. Use only wood or plastic scrapers for removing the sludge and curdled paint. Normally, latex and acrylic paints will not cause staining. Oil-based paints, linseed oil, putty, caulks and sealants may cause oily stains.

Water Spots and Rings (surface accumulation of hard water) Buff with dry 0000 steel wool.

Fire and Smoke Damage Older stones and smoke or fire-stained fireplaces may require a thorough cleaning. When the smoke is removed, there may also be some etching (due to carbonic & other acids in smoke). Commercially available “smoke removers” may save time and effort.

Etch Marks (caused by acids left on the surface of the stone) Some materials will etch the finish but not leave a stain. Others will both etch and stain. Contact your stone dealer or call a professional stone restorer for refinishing or re-polishing etched areas.

Efflorescence (a white powder that may appear on the surface of the stone) It is caused by the deposition of mineral salts carried by water from below the surface of the stone. When the water evaporates, it leaves the powdery substance.

If the installation is new, dust mop or vacuum the powder. You may have to do this several times as the stone dries out.

Do not use water to remove the powder; it will only temporarily disappear. If the problem persists, contact your installer to help identify and remove the cause of the moisture.

Efflorescence

Scratches and Nicks Slight surface scratches may be buffed with dry 0000 steel wool. Deeper scratches and nicks in the surface of the stone should be repaired and re-polished by a professional.

 

What are the vibration risks associated with operating cleaning machinery?

Activities such as operating a fork lift truck, rotary buffer or ride-on scrubber drier can cause fatigue, insomnia, headaches and shakiness with symptoms similar to those that many people experience after a long car or boat trip.

After daily exposure over a number of years, these same whole-body vibrations can result in a number of health disorders affecting your entire body including permanent harm to internal organs, muscles, joints and bone structure.

The risks linked to long-term exposure to strong or high frequency vibrations depends on the type of stress experienced, whether this is skeletal or muscular, or even to the vascular and nervous systems.

There are two main classifications of vibration:

Hand-arm vibrations (common to rotary buffers, walk-behind scrubber driers and ride-on machines)

Rotary buffer

Whole-body vibrations (specific to ride-on machines)

013-cs60-casse2-rgb

1. Hand-arm vibrations: ISO 5349-1

It is well known that vibrating hand tools and therefore exposure to high frequency vibrations interfere with blood circulation (vascular effects) and nerves signals (neurological effects – sometimes resulting in partial paralysis of the thumb’s radial nerve), thereby causing a tingling sensation, loss of feeling, numbness and a characteristic blanching or whitening of the affected parts of the hand-arm system known as “white-finger”.

HAV_Hand

Exposure to the vibrations of heavy tools (the most typical example being the pneumatic drill) may damage the osteo-articular system (resulting in arthrosis or bone decalcification).

It is important therefore to consult the Use and Maintenance booklet for any piece of equipment being utilised to see the level of vibrations transmitted to the hand-arm system.

Check the level of vibrations transmitted to the hand-arm system (expressed in m/s²) and, if possible, choose the one with the lowest level. The level of vibrations should be measured in compliance with ISO 5349-1.

2. Whole-body vibrations: Jolts ISO 2631-1

The whole-body vibrations of a person are commonly called ‘jolts’. When these are very strong or prolonged, they may lead to spinal problems mainly relating to bone and muscular disorders.

Vibration energy waves, much the same as noise, are transferred from the energy source – a hand tool or vehicle – into the body of the exposed operator. This is then transmitted through the body tissues, organs and skeletal systems of the individual before it is dampened and dissipated.

The symptoms of whole-body vibration are not so readily recognisable and are often mistaken for other unrelated conditions and ailments. The health outcomes are non-specific and can be difficult and extremely expensive to identify, manage and control.

These factors should not detract from the fact that employees, and in particular professional drivers, can suffer debilitating ill health effects from whole-body vibration exposure.

The most common medical conditions experienced through long term exposure to whole-body vibrations are:

  •  Spinal column complaints are perhaps the most common issues associated with the long-term exposure to whole-body vibration, where the back is especially sensitive to the 4-12Hz vibration range
  •  Digestive system issues are often observed in persons exposed to whole-body vibration over a long period of time. This is associated with the resonance movement of the stomach at frequencies between 4 and 5Hz
  •  Cardiovascular system effects resulting from prolonged exposure to whole-body vibration at frequencies below 20Hz. These result in hyperventilation, increased heart rate, oxygen intake, pulmonary ventilation and respiratory rate.

Fortunately the human body can tolerate certain levels of vibration energy but when exposed over a long period of time it begins to deteriorate and fail causing a disruption in the body’s natural processes and systems.

The health effects experienced by employees vary considerably and factors such as situation, age, lifestyle (smokers), posture, ergonomic design and resonance all have an influence on the ill health effects of the vibration exposure.

The problems may be caused through the incorrect position of the operator (resulting from bad machine use habits) or a machine design that fails to take into account the basic principles of ergonomics.

The onus is on the employer to know the vibration exposure that their workforce is exposed to, including the magnitude of vibration, distribution of the motion within the body, and the frequency, direction and duration.

Check the level of whole-body vibrations (expressed in m/s²) in the machine Use and Maintenance booklet and, if possible, choose the one with the lowest level. The level of vibrations should be measured in compliance with ISO 2631-1. Ensure the machine EC declaration states that it has been designed in compliance with directive EN 12100, and that the principles of ergonomics have also been applied.

The level of hand-arm vibrations of Comac scrubber driers, sweepers and single disc rotaries is certified by an accredited laboratory to offer the highest reliability of the declared values.

Battery maintenance for floor cleaning equipment

Choosing the right battery for your scrubber drier or sweeper, understanding proper battery maintenance and educating machine users are just a few important ways to ensure the safe, uninterrupted operation of your floor machines, and are key to getting the biggest return on your battery investment.

So what battery technology do you choose?

Deep-cycle batteries, whether they are flooded, AGM or gel, are the best choice for cleaning machines because they are optimised for deep discharge, characteristic of regular machine operation.

batteries

Flooded versus sealed (AGM or gel) technology is a decision based on budget or environmental regulations at an individual location. Flooded batteries cost less and have a longer life-cycle, while sealed AGM or gel batteries are maintenance-free but have a higher price. Preference really depends on one of these two requirements.

Battery box

Maintaining water levels is the key to maintaining flooded batteries. Despite the multitude of challenges impacting the floor cleaning industry today, equipment inefficiencies due to the failure of watering deep-cycle flooded batteries shouldn’t be one of them.

watering systems

Single-point watering systems are gaining in popularity as they make maintenance of deep-cycle flooded batteries quick and easy. With a battery watering system, staff can fill a complete set of batteries in less than 30 seconds.

Regardless of which battery technology you choose, it’s important to remember that a battery is only as good as the maintenance it receives. Proper maintenance of deep-cycle batteries will provide maximum performance and longer life extending your overall equipment run times and return on investment.

A common problem often encountered is users who have let batteries discharge too far. This can shorten the life of batteries and it is so critical to avoid this, and some manufacturers now have an electronic ‘low battery cut-off system’ that prevents this from happening.

Following a few simple maintenance steps ensures that your machine’s deep-cycle batteries will provide optimum performance levels day in, day out.

Tips for Proper Maintenance:

Safety

The safety precautions and procedures outlined below should be followed whether handling flooded lead acid (FLA) or valve regulated lead acid (VRLA) such as AGM or gel batteries.

‐Always wear protective clothing, safety glasses and gloves when handling and/or performing battery maintenance

‐Never add acid to a battery

‐Keep batteries clean and dry

‐Keep sparks, flames and cigarettes away from batteries

‐Charge only in well ventilated areas

‐Avoid skin contact with the electrolyte

‐Always use insulated tools

Charging

chargers

‐Charge after each use and follow the manufacturer’s charging instructions

‐Before charging, ensure the electrolyte level is above the plates in flooded batteries

‐Tighten vent caps before charging

‐Do not interrupt a charge cycle

‐Never allow batteries to freeze and never attempt to charge a frozen battery

‐Avoid charging at temperatures above 120°F (49°C) and always keep batteries away from heat sources. High heat kills batteries.

Watering (flooded batteries only)

‐Add water only after fully charging the battery (unless plates are exposed)

‐Check with the manufacturer regarding proper electrolyte fill levels

‐Never allow the electrolyte level to fall below the plates

‐Use distilled water

Cleaning

‐Clean the battery terminals and cable lugs regularly with a solution of baking soda and water using a wire brush. It is imperative to properly maintain the entire connection in a flooded battery because corrosion at either end of the connection can  cause high resistance and potential battery failure. Rinse with water and dry.

‐Thinly coat all connections with anti-corrosion spray or silicone gel to resist corrosion

Torque

‐Tighten all wiring connections as per the manufacturer’s specifications

‐Do not over-tighten as this can result in breakage of the battery terminals

‐Avoid under-tightening as this could lead to terminal meltdown

‐Make sure there is good contact with the terminals

Storage

There are important steps that should be followed when storing batteries for an extended period of time.

‐Completely charge batteries before storing and monitor every six weeks while in storage

‐Batteries gradually self-discharge during storage. AGM batteries self-discharge at a much slower rate than flooded batteries. Be sure to monitor voltage every 4 to 6 weeks. Stored batteries should be given a boost charge when they are at 70 percent state of charge or less.

‐Store batteries in a cool, dry location avoiding areas where freezing or very hot temperatures are expected

‐Keep batteries fully charged to prevent freezing

‐When batteries are taken out of storage, recharge them before use

‐Avoid direct exposure to heat sources, such as radiators or heaters

Gaining a clear understanding of the various deep-cycle battery types and maintenance practices ensures that your battery-powered floor machines will continue to operate at peak levels of performance and reliability. With proper care and maintenance, an initial investment in deep-cycle flooded, AGM or gel battery technology can be extended as well as keeping the total cost of ownership to a minimum resulting in more uptime and greater profits for your company.

When it comes to battery maintenance, the bottom line is that with proper maintenance, batteries can serve users for years to come.

Cleaning Sports Hall Floors

Cleaning sports hall flooring is an essential part of regular maintenance. Not only will it make the floor look more visually appealing, but it will also extend the timeframe between scheduled floor sanding and refurbishment.

sportshallandcourts

We recommend our 5-step process for cleaning sports hall flooring:

1. Always pre-sweep floors

The most important way to protect the floor is to dust mop / sweep on a daily basis to remove grit, dirt and other dry debris. This dirt can otherwise act like sand paper on the floor seal causing erosion over time.

Begin with a pre-sweep of the floor to remove all dry grit, dust, fibres and hair. Doing so will make the actual cleaning of the hall far easier.

Avoid using dust mopping systems that use oil based or even water based treatments to hold and retain dust. These can leave a residue behind, trapping dirt which can then scratch the finish and which could be slippery and potentially dangerous.

Use a scissor mop or V-sweeper that will trap and hold dirt without any chemicals, and cover a larger area than a flat mop.

scissorsweepsportsfloor

2. Make sure you DO wet clean the floor

Athletes perspire. Perspiration, or sweat, and body oils are high in protein and salt which will build up over time. Solvent based cleaners and too little water will not break down the residue and can lead to a dull, slippery floor. Wet cleaning of some type, either mopping or automatic scrubbing combined with the proper wood floor cleaner, will remove these films.

sportshallfloor2

3. Always use a scrubber drier when possible

Mopping is fast becoming a thing of the past, especially in large areas like sports halls, due to limitations on productivity and how damp the floor remains.

Using a scrubber drier leaves the floor drier and much cleaner. Depending on the size of machine you use, a sports hall floor can be clean and dry within 45 minutes with very little effort.

As long as the floor is in good condition and there is a quality finish, there is no concern about moisture or weight issues when cleaning hard wood sports floors.

Using a scrubber drier is a great way to clean a wooden sports hall as wood doesn’t like having too much water left on the surface as it will begin to expand if the water is soaked up by the wood.

A scrubber drier will leave the floor almost dry after passing over the floor. Remember, always use as little water as possible for cleaning hardwood sports flooring.

benessere2[1]

4.  Use the right products on the floor

Do not throw any and all types of cleaners at the floor in an attempt to solve an issue. This will only result in damage to the finish and/or the wood itself. Use a cleaner recommended by the flooring manufacturers / contractors for any wet cleaning you perform.

A good cleaner would generally be an alkaline based cleaner along the lines of Granwax Sportsclean or Junckers SYLVA Cleaner.

sportsclean[1]

These will help remove all traces of grease and the dirty marks that are left on the floor and on the sports lines. Sometimes it might be necessary to apply the floor cleaner in higher concentration as a pre-spray leaving it for a few minutes in order to remove all black rubber sole marks.

5. Preventative maintenance – Protect the floor!

Hardwood sports flooring is designed to withstand many types of activities. However, furniture such as chairs, certain types of equipment and hard plastic or metal casters can damage the floor.

Make sure everyone that uses the floor takes appropriate steps to keep the floor protected during events.

There are many types of floor covers and mats that can make protecting and cleaning hard wood sports floors much easier.

Schools-500-Games-June-2012-2

Use large barrier matting to protect the floor from grit and water. Clean and replace the matting regularly.

Finally, check ventilation and heating systems to prevent condensation and use cleaning products without wax content.

Warehouse floors – forklift truck tyre marks and their removal

A clean and tidy industrial floor will improve the aesthetics of any warehouse and also satisfies safety requirements demanded by H&S bodies.

In order to keep industrial floors in the best possible condition it is important that a good cleaning programme is implemented.

Sweep floors clean

It is important that industrial floors should be well maintained and kept clean and free of any loose debris that could otherwise abrade the surface. Use large brooms, scissor sweepers or where size and budget permits walk behind or even ride-on sweepers for large warehouse facilities.

013-cs60-casse2-rgb

Remove grime

Depending upon the size of the floor, the use of a mop and bucket for small areas is viable but for deep cleaning and certainly for larger expanses of floor area, a scrubber drier is better suited to remove any grease, spillages or general grime.

Rubber tyre marks

A major problem in maintaining an industrial floor is the tyre marks left behind from forklift trucks.

These marks become more apparent and troublesome when a light reflective floor is involved, and can detract from the aesthetic appearance and reduce the performance characteristics of the floor surface.

Warehouse floors

The removal of ingrained tyre marks can in many cases be extremely difficult, if not impossible. Therefore it is strongly advisable that a cleaning programme is put in place to manage the situation.

Forklift Truck Tyres

The most common forklift truck tyres are made from a universal rubber compound. This type of tyre will leave marks on concrete floors.

There are two types of “non-marking” tyres available and these should be considered for use where tyre marking becomes a problem.

“White” tyres are made from synthetic rubber with white silica gel or resin instead of carbon. The white tyres have a grey-white appearance, can cost up to 25% more than the universal carbon tyres and have about 90% of the life of the universal tyres.

They can also have a heat build-up problem when running fast and/or over long distances. If heat does build up then the load capacity can be reduced. These tyres can leave a white dust-type residue, which does not adhere to the floor surface and can be swept up during the cleaning process.

Polyurethane tyres are shiny black in appearance, very hard and can cost twice as much as universal rubber tyres. It is suggested that polyurethane tyres wear three times more than the universal tyre. The polyurethane tyre will leave a black residue that does not stick to the floor unlike black rubber type tyres. This non-sticking allows the residue to be swept or vacuumed through the maintenance cleaning process.

Spinning is the main contributory factor to black rubber tyre marks. This is a particular concern for light reflective floors. This practice must be discouraged where possible.

Recommended method for cleaning and removing rubber tyre marks

Envii EN701 Rubber Tyre Mark Remover (Ultragreen & Non-Hazardous) removes rubber marks with ease. It is able to tackle the most difficult rubber deposits whether it be from a forklift or the landing area on a runway.

It is ideal for busy warehouse or distribution centres where time is at a premium and areas cannot be closed off for long periods.

Use neat for heavy rubber tyre marks where 100ml will normally treat 1m² or it can be diluted to deal with lighter marks or for ongoing maintenance.

Another product we have found from experience that works well is Ultrapac Renovate from Prochem. It can be used as a pre-spray and can work wonders on rubber tyre mark removal. This product is solvent free and is designed for the removal of ingrained soils, carbon, soot and rubber from hard and semi-porous surfaces.

UltraPac Renovate

After application of a rubber tyre mark remover, the area can be scrubbed with a scrubber drier using hard polypropylene scrubbing brushes or with green scrubbing pads to loosen the residue. The scrubber drier can be filled with water and / or a water and detergent mix to remove excess solution from the floor surface and provide a final clean in the process.

A recommended chemical for this process, and for regular maintenance cleaning of warehouse floors, is Triple Advanced Scrubber Drier Detergent manufactured by Selden. The super strength formulation of this product removes even the toughest grease and grime and is designed for cleaning large warehouses.

Polypropylene scrubbing brushes or green scrubbing pads are recommended for use with scrubber driers to clean warehouse floors. Do not use black pads to clean any marks from a light reflective floor surface as they are extremely aggressive and may scratch the floor surface.

Depending upon the size of the warehouse, the space between pallets and racking, and of course the budget available, scrubber drier options include everything from mid-sized walk behind machines such as the Comac Abila or Simpla, to larger machines such as the Comac Omnia 32, and then upwards to include ride-on machines such as the Comac Flexy and Comac Ultra 120.

Ultra-RGB[1]

Safe and sensible activities

The loading and unloading of warehouse racking and pallet bays and the movement of goods around warehouses needs to be carried out with care to minimise surface marking and scratching.

Forklift trucks and other vehicles need to be driven with care over these surfaces to avoid marking caused by wheel spin, sharp and abrupt turning or sliding, leaving unsightly marks that need to be removed.

Even a properly planned maintenance schedule cannot prevent the leaving of rubber tyre marks if the forklift trucks are not handled appropriately and with care.

The benefits of leasing cleaning equipment

Leasing your cleaning equipment makes sense in lots of ways. Here are some of the key benefits:

Improve Cashflow

Your new equipment can be installed and operational without the need for capital expenditure. The cash can then be used where it will produce the best return, such as in investment, operating activities or short term funding needs.

Retain Credit Lines

Keep existing banking arrangements, and credit lines free for more appropriate uses. Lease finance facilities cannot be withdrawn like overdraft facilities.

Simplify Budgeting

With finance payments fixed for the whole term helps avoid the effects of inflation and making cash flow forecasting and budgeting simpler. Bank facilities are generally related to interest rates, which is fine when they are low but can cripple cashflow when they increase.

Keep Up To Date

Combat obsolescence problems or requirement changes as the equipment can be supplemented or upgraded at any time in the future.

Let the Equipment Pay for Itself

Enable the finance payments to coincide with the benefits of having the new equipment as they start to appear. After all, you wouldn’t pay all your staff costs up front! Finance payments may be financed as you go along by extra income obtained by having the new equipment. Have equipment at today’s prices paid for from tomorrow’s income.

Tax Savings

In the case of lease rental, all rentals paid are 100% allowable as an expense for tax relief often providing tax savings.

lease_example[1]